Da Vinci On-Line
Operating Instructions

 

 

A. Lock/Loosen lever: allows model/platform to rotate 360 degrees

B. Lock/Loosen lever: allows model to be tilted and locked at desired angle

C. Lock/loosen knob: locks model on tilt platform

D. Motor/Collet

E. Motor Lock/Remove (screw&nut)

F. Motor Speed Control

G. Motor On/Of Switch

H. Motor Arm Spindle

I.  Adjustment: Motor Arm Spring Tension

J. Lock/Loosen of Motor Arm

K. Lock/loosen lever: to raise or lower all arms

L. Lock/Loosen the (secondary arm) Split Arm

M. Lock/Loosen rotation of primary arm

N.  Lock/Remove Motor Arm

O.  Vertical Adjustment: Motor Arm Depth Stop

 P.  Anti-rotation shaft collar can be used as depth stop when drilling

Q.  Motor spindle lock button (Lock/Loosen Collet)

R.  Survey spindle tension collar

S.  Lock/Loosen chuck

T.  Adjustable chuck

U.  Hand rest

V. Vertical adjustment of hand rest

W. Articulated (hand rest) arm right & left

X.  Adjustable feet (not shown)  

 

Milling Procedures

 

Lock model on platform using knob (C).  Tilt to desired angle and lock in place with lever (B) and (A).

 

Insert desired bur/cutting tool leaving only the cutting part of the tool extending beyond the collet, tighten collet using the wrench provided

(See accompanying safety instructions).

 

Adjust vertical height of articulated arms.  Loosen/Lock lever (K) coarse adjustment or knob (I) fine adjustment. 

 

Set speed by turning knob (F) to the maximum RPM desired when foot pedal is depressed.

 

If unfamiliar with procedures, a milling class is highly recommended.

 

Observe:  Before operating use all safety precautions and good common sense 

Observe Previous Warning and Precautions

SPECIAL SAFETY INSTRUCTIONS:

  

Remember, Use Approved Safety Goggles.

 

When inserting a bur/cutting tool into the motor, be certain that it is inserted all the way into the collet.  There should be a minimal amount of extension of the cutting tool.  Excess amount of extension of the cutting tool can be dangerous, especially high speeds. 

Using the provided wrench, tighten collet sufficiently.  Spin spindle by hand to confirm that the cutting tool is turning straight. (I.E., Centric).  If not, repeat procedure until the bur/cutting tool etc. turns straight and true. Be certain the cutting tool is appropriate and in good condition. 

Never run motor at full speed without a load on it.  (I.E., without milling-drilling etc.) 

Persons in the vicinity also need to use safety goggles and dust masks. 

USE THIS UNIT IN CONJUNCTION WITH AN APPROVED VACUUM SYSTEM and DUST MASK . 

Replace any damaged, worn or improperly functioning parts.

 

Always heed all safety precautions!

 

 

Observe:  Before operating use all safety precautions and good common sense

 

 

Persons in the vicinity also need to use safety goggles and Dust Mask.

 

 

USE THIS UNIT IN CONJUNCTION WITH AN ADEQUATE VACUUM SYSTEM.

 

Replace any damaged, worn or improperly functioning parts.

 

Familiarize your self with the features and functions of various aspects and components of the unit.  (See diagram).

 

Approved safety goggles and dust mask are required for user and other persons in area.

 

Use this tool in conjunction with an adequate dust collector.

 

Do not use damaged or improperly working tool.  Have it repaired first.

__________________________________________________________________________________________________________________________________________________

Separate Diagram Letters refer to this illustration only. 

 

Always heed all safety precautions!

 

Diagram of drill attachment

 

A. Spring adjustment /Thumb screw

B. Depth stop /Thumb screw

C. shaft

D. Friction adjustment thumb screw (on opposite side)

E. Anti-rotation drilling attachment body

F. Knob to lock attachment